AR0141CS2C00SUEA0-DR

AR0141CS2C00SUEA0-DR is a CMOS image sensor from the Aptina/Onsemi AR0141 family. It is a compact, color imager designed for embedded/automotive and machine-vision applications. The sensor provides about 1.3 megapixel active resolution with 3.75 µm pixels and uses a rolling-shutter CMOS process. It outputs data over MIPI CSI-2 (typically via a 2-lane interface) and supports features such as programmable exposure and gain, region of interest (ROI)/windowing, binning, black level calibration, and test-pattern outputs. The “DR” suffix indicates a specific device/revision and packaging variant (e.g., RoHS/tape-and-reel version). Frame rate depends on resolution/ROI; higher with windowing. Power and sensitivity are optimized for typical indoor/outdoor lighting. Typical applications include machine-vision cameras, robotics, drones, automotive driver-assistance subsystems, and surveillance. For exact electrical specs (sensor size, full frame rate, dynamic range, latch timings), consult the official datasheet for this exact part variant.

AR0141CS2C00SUEA0-DR is an Aptina/ON Semiconductor 1.0 MP CMOS image sensor. Key features:
- Optical format: ~1/4"; active area around 1280×960 (approx. 1.23 MP)
- Pixel size: ~3.75 µm
- Shutter: rolling shutter
- Frame rate: up to full-res ~tens of fps (ROI/windowing increases rate)
- Interface/output: digital MIPI CSI-2 (2-lane) with RAW Bayer data
- Bit depth: 12-bit digital output (per pixel)
- Core/IO voltages: typically 1.8 V core, 1.8–3.3 V I/O
- Programmable controls: exposure, gain (AGC), white balance
- On-chip features: BLC/LSC, defective pixel correction, some noise reduction, ROI/windowing, binning
- Range of operation: industrial/embedded environments; typical temp range -40 to 85 °C
- Package: CS2C00SUEA0-DR variant
Note: exact numbers (frame rate, DR, voltage, temp) depend on revision; consult the datasheet for precise specs.

CS2 refers to the Chip-Scale Package (CSP) packaging for the AR0141 sensor.

AR0141CS2C00SUEA0-DR is supplied in a 48-pin LGA/LFCSP-style package (48 pins total). Major pin functions (grouped):
- Power/Ground: multiple VDD domains (analog, core, I/O) and GND pins.
- Clock: Master clock input (MCLK).
- Serial interface: I²C/SCCB control pins (SDA, SCL) for register access.
- Data outputs: MIPI CSI‑2 high-speed differential pairs (clock + data lanes) for image data; legacy/parallel timing outputs on variants (PCLK, HSYNC, VSYNC) if supported.
- Control: RESET, PWDN/standby, and several GPIO pins.
- Misc/test: dedicated test/config pins and reserve pins for factory use.
For the exact pin map and electrical/functional descriptions refer to the official AR0141 datasheet and the package pinout drawing.

Manufacturer: ON Semiconductor (formerly Aptina Imaging).
Type of company: a global semiconductor company that designs and manufactures integrated circuits and image sensors (including the AR0141 CMOS global‑shutter image sensor) and other analog, power-management, and imaging products for automotive, industrial, and consumer markets.

AR0141CS2C00SUEA0-DR is a CMOS image sensor used for general imaging. Common application areas:
- Machine vision and factory automation (inspection, barcode/OCR)
- Surveillance and security cameras
- Automotive imaging (rear-view, ADAS)
- Robotics and drones
- Industrial inspection
- Medical imaging/endoscopy
- Consumer electronics and video capture devices

Direct equivalents: other ON Semiconductor AR0141CS family part numbers (same die with different package suffixes, e.g., alternate -DR/-TR variants).
Functional substitutes: sensors with equivalent specs (1.2MP, 1/3" optical format, global‑shutter) — e.g., Aptina/ON MT9M001 or comparable Teledyne/OmniVision global‑shutter parts.
Always verify datasheets/pinout and timing before substituting.